Use Sodium Hydroxide Floor Sign to identify, raise awareness and promote safety practices where sodium hydroxide is used, handled, or stored. Due to its strong corrosive qualities, exposure to sodium hydroxide in its solid or solution form can cause skin and eye irritation, as well as burn or eat away at any part of the body that it contacts. It is important to take extra precautions when handling and storing sodium hydroxide.
Non-Slip Materials
Two grades of adhesive-backed vinyl floor signs are available. Both are protected with non-slip, water resistant laminates.
Apply to smooth, clean, dry, and even surfaces. Buyer should test in non-conspicuous area before proceeding.
When removed, there may be some residue of adhesive that can be removed with detergent, depending on the surface. It’s also possible the adhesive will remove dirt from the surface, leaving the appearance of residue.
20 Mil Heavy-Duty Semi-Permanent Adhesive-Backed Vinyl with Textured Water Resistant Anti-Slip Laminate
- Textured surface. Indoor/outdoor.
- Temporary use on low-pile carpeting. 20 mil.
- Resistance: Water, Mild Detergents
Laminated with a textured, non-slip surface that also protects against water and mild detergents.
Apply to smooth, clean, dry, and even surfaces in excellent condition, indoors or outdoors. May also be used temporarily on most low-pile carpeting for several months. Avoid areas that are subject to traffic from heavy equipment, such as forklifts. Do not overlap floor signs.
To apply, be sure the floor is above 55° F. Clean floor prior to application. A small amount of water may be lightly sprayed over the placement area to make installation easier. Starting at one corner, simultaneously peel backing paper and apply floor sign to floor. Smooth out lightly using a squeegee from the center to the edges. Do not smooth with your hands. Continue with firm, overlapping strokes from the center out to each edge, peeling back the paper backing as you go. Be sure that all edges and corners are firmly attached.
After applying, do not scrub or polish area on or surrounding floor signs for at least 48 hours. After 48 hours, the floor sign will maintain adherence within the service temperature range of -40° to 120° F.
When removed, there may be some residue of adhesive that can be removed with detergent, depending on the surface. It’s also possible the adhesive will remove dirt from the surface, leaving the appearance of residue.
Our durable anti-slip floor signs will stick to most smooth, clean, dry surfaces both indoors and outdoors. They can also be used temporarily on most low-pile carpeting for several months. Buyer should test in non-conspicuous area before proceeding.
These heavy-duty floor signs can be removed. Depending on the surface, there may be some residue of adhesive that can be removed with detergent. It’s also possible the adhesive will remove dirt from the surface, leaving the appearance of residue. Buyer should test in non-conspicuous area before proceeding.
10 Mil Commercial-Grade Removable Adhesive-Backed Vinyl with Embossed Water Resistant Laminate
- Smooth surface. Not for use outdoors or on carpet. 10 mil.
- Resistance: Water, Mild Detergents
Laminated with a smooth, non-slip surface that also protects against water and mild detergents.
Apply to smooth, clean, dry, and even surfaces in excellent condition. May be used on commercial floor tiles, sealed wood, sealed concrete, waxed vinyl, marble, terrazzo, and ceramic tiles. Not for use outdoors or on carpet. Avoid areas that are subject to traffic from heavy equipment, such as forklifts. Do not overlap floor signs.
To apply, be sure the floor is above 50° F. Clean floor prior to application. A small amount of water may be lightly sprayed over the placement area to make installation easier. Starting at one corner, simultaneously peel backing paper and apply floor sign to floor. Smooth out lightly using a squeegee from the center to the edges. Do not smooth with your hands. Continue with firm, overlapping strokes from the center out to each edge, peeling back the paper backing as you go. Be sure that all edges and corners are firmly attached.
After applying, do not scrub or polish area on or surrounding floor signs for at least 48 hours. After 48 hours, the floor sign will maintain adherence within the service temperature range of -40° to 120° F.
When removed, there may be some residue of adhesive that can be removed with detergent, depending on the surface. It’s also possible the adhesive will remove dirt from the surface, leaving the appearance of residue.
